Roller Blinds - Assembly Instructions

Our roller blinds can be mounted on the wall, on the ceiling or directly on the frame according to your needs. Below you will find instructions for the three types of assembly. For a correct installation you should have the following tools: screwdriver, drill, pencil, measuring tape, spirit level and a little patience.

A-Roller Blinds - Wall Mounting

1-Measure the width of the complete window.

• Measure the total width of the roller blind.

• Using a measuring tape and pencil, mark the ends of the total size of the tent ordered by you on the wall, taking care to mark both ends and center it with respect to the size of the window.

• For the height, calculate 10/15 cm above the window frame.



2-Once you have marked the maximum width of the curtain centering it on the window, put the support plates on the ends and make the marks for the holes.

• Attention: align the two ends with the level for a perfect horizontal position.



3-Starting from the side where there is the command / chain of the roller blind, drilled with the drill where you have marked the holes. Put the dowels and screw the support bracket.

• We recommend, before piercing the opposite side, to take the roller blind and insert it into the assembled support to check the exact position of the holes to be made on the opposite side.

• After verification, proceed to mount the opposite bracket.

• Warning: the brackets must be firmly fixed to the wall.



4-Fix the blind by first inserting the chain side and then the side with the pin until you hear a click.

• Pay attention to the correct positioning of the up / down mechanism.

5- Descend the tent a couple of times by pulling the chain.

• Probably during transport the fabric will have moved slightly; check whether it is centered on the tube, otherwise completely unroll the fabric, detach the sheath from the tube, move it slightly and center it on the tube.



6-Now if you wish, you can mount the limit switches on the chain.

• Curtain limit switch closed: completely wind the curtain and, with a slight pressure, insert the stop on the chain that activates the
closing command at the shell.

• Open curtain limit switch: open the blind up to where you intend to let it arrive and, with a slight pressure, insert the stop on the chain that activates the opening command in correspondence with the hood Figure A.

• In the presence of children, you can mount the safety device. Figure B



_____________________________________________________________________________________________________________________

2-Roller Blinds - Ceiling Mounting

1-Ceiling Mounting

• measure the width of the complete window. B

• Measure the total width of the roller blind. A

• Using a measuring tape and pencil, mark the ends of the total size of the tent you ordered, on the ceiling, taking care to mark both ends and center it with respect to the size of the window.

• Attention: calculate the projection of any handle or sill. C

2-Once the width of the blind is marked on the ceiling, place the support plates on the ends and mark
them to make holes.

• Attention: The holes of both ends must be equidistant from the wall

3-Starting from the side where there is the command / chain of the roller blind, pierced with the drill where you have marked the holes. Put the dowels and screw the support bracket.


• We recommend, before piercing the opposite side, to take the roller blind and insert it into the assembled support to check the exact position of the holes to be made on the opposite side.
• After verification, proceed to mount the opposite bracket.
• Attention: the brackets must be firmly fixed to the ceiling.



4-Fix the blind by first inserting the chain side A and then the side with the pin B until you hear a click.
• Pay attention to the correct positioning of the down-shift mechanism.



5-Take the roller blind back and forth a few times by pulling on the pull chain

• It could be that the fabric of the roller shade has moved during transport. Then check if the fabric is centered on the tube; otherwise unroll it
completely, remove the cover from the tube, move it slightly and center it again.

6-Now if you wish, you can mount the limit switches on the chain.

• Curtain limit switch closed: completely wind the curtain and, with a slight pressure, insert the stop on the chain that activates the
closing command at the shell.

• Open curtain limit switch: open the blind up to where you intend to let it arrive and, with a slight pressure, insert the stop on the chain that activates the opening command in correspondence with the hood Figure A.

• If you have children, you can mount the safety device. Figure B



_____________________________________________________________________________________________________________________

3-Roller Blinds - Windows Mounting

1-Measure the total width of the roller shade including attachments

• Place the last part of the blind where the handle is and center it on the glass

• Make the measurements at the end of the window with a meter and a pencil.
• Warning: If you have two doors, do the same operation with the other roller shade

2- After marking the width of the curtain on the window frame, place the support plates on the ends and mark the holes
• Warning: the holes must be perfectly aligned

3-From the side where the command or chain is located, screw the bracket to the markings using the appropriate screws. If you have aluminum
frames, make a small hole to insert the supplied screw 

• Before making a hole on the opposite side, take the shade and insert it into the bracket to check the exact position of the holes
• Mount the opposite bracket 

• Attention: The brackets must be firmly attached to the frame

4-Lock the roller shade by first inserting the side of the pull chain and then the side with the pin until you feel a click
• Pay attention to the correct positioning of the up / down mechanism

5-Take the roller blind back and forth a few times by pulling on the pull chain

• It could be that the fabric of the roller shade has moved during transport. Then check if the fabric is centered on the tube; otherwise unroll it
completely, remove the cover from the tube, move it slightly and center it again.

6-Now if you wish, you can mount the limit switches on the chain.

• Curtain limit switch closed: completely wind the curtain and, with a slight pressure, insert the stop on the chain that activates the
closing command at the shell.

• Open curtain limit switch: open the blind up to where you intend to let it arrive and, with a slight pressure, insert the stop on the chain that activates the opening command in correspondence with the hood Figure A.

• If you have children, you can mount the safety device. Figure B